Search found 9 matches

by Rufus
Fri Jan 20, 2023 5:06 am
Forum: General Questions
Topic: AF Closed Loop Control
Replies: 10
Views: 6929

Re: AF Closed Loop Control

Hello. Thanks KTuner & Linszter for patiently answering my questions :) While ECT is at normal operating temperature … Can KTuner operate closed loop using inputs from a) wideband O2, b) rpm, and c) engine load to control mixture ratio over the entire rpm and load operating range of the engine? ...
by Rufus
Fri Jan 13, 2023 11:10 pm
Forum: General Questions
Topic: AF Closed Loop Control
Replies: 10
Views: 6929

Re: AF Closed Loop Control

Does WOT enrichment only apply at 100% load, and then the AF immediately goes to the base target value as load drops: 99% … 98% … etc? Or is there more to it?

Not looking for any suggested values. Just wanna make I understand what the system capabilities are.

Regards,
Bob
by Rufus
Fri Jan 13, 2023 10:38 pm
Forum: General Questions
Topic: AF Closed Loop Control
Replies: 10
Views: 6929

Re: AF Closed Loop Control

Thanks
by Rufus
Fri Jan 13, 2023 8:07 pm
Forum: General Questions
Topic: AF Closed Loop Control
Replies: 10
Views: 6929

Re: AF Closed Loop Control

“Once you engage enrichment those target tables become the AF targets …”

Where is enrichment engaged? In a fuel (injector pulse width) table?
by Rufus
Fri Jan 13, 2023 6:58 pm
Forum: General Questions
Topic: AF Closed Loop Control
Replies: 10
Views: 6929

Re: AF Closed Loop Control

“So does KTuner allow closed loop fuel control using target AF’s over the entire speed / load operating ranges when ETC is fully warm? …

What authority does the End User have with inputs to accomplish this?”

I should add … while controlling AF to 14.7 @ low load and 12 @ full load, for example.
by Rufus
Fri Jan 13, 2023 6:24 pm
Forum: General Questions
Topic: AF Closed Loop Control
Replies: 10
Views: 6929

Re: AF Closed Loop Control

Excellent. Thanks, I understand a little better now :) So does KTuner allow closed loop fuel control using target AF’s over the entire speed / load operating ranges when ETC is fully warm? (I.e. with no switching between open & closed loop?) What authority does the End User have with inputs to a...
by Rufus
Fri Jan 13, 2023 12:45 am
Forum: General Questions
Topic: AF Closed Loop Control
Replies: 10
Views: 6929

AF Closed Loop Control

Hi - Planning a swap of an ‘06 MY K20Z1 & W2M5 into my ‘87 CRX Si. I’m considering use of the KTuner End User ‘05-‘06 RSX / Swap System ECU. Questions about closed loop Target AF control. I see a “base” Target AF mentioned on the “Closed Loop Settings” page which mostly sets conditions for switc...
by Rufus
Fri Sep 30, 2022 9:28 pm
Forum: General Questions
Topic: K20A into an ‘87 CRX Si?
Replies: 1
Views: 3107

K20A into an ‘87 CRX Si?

Hello- I’m planning a K transplant into my ‘87 CRX Si using a Hasport kit. Hoping to source a 2007-2011 JDM Civic Type R K20A engine, a 2002-2006 base RSX W2M5 5spd transmission and a 37820-RSP-E01 through E03, or 37820-RRC-J01 through J04 ECU. Beside not planning any engine modifications, I plan to...
by Rufus
Fri Sep 30, 2022 7:22 pm
Forum: Welcome
Topic: My first time here …
Replies: 1
Views: 3473

My first time here …

KTuner Hi - Retired automotive engineer, and long time hands-on car enthusiast. Experience with a variety of sports and performance cars. Built an ERA Cobra. Honda ownership includes an ‘84 Prelude, ‘87 CRX Si, ‘03 S2000, and ‘16 Accord. Have a little EFI diagnostic experience, but limited to ‘80’s-...

Go to advanced search