Search found 13 matches
- Wed Aug 23, 2023 12:12 am
- Forum: General Questions
- Topic: Oil guage to 0-5v input?
- Replies: 1
- Views: 2093
Oil guage to 0-5v input?
Quick question, I have a 0-100psi Auto-meter oil pressure sensor that has one wire that runs to a analog guage, can I run that same wire to one of the 4 Analog inputs on my End-user R1 board and set the guage up on the software?
- Mon Aug 21, 2023 10:38 pm
- Forum: General Hardware Questions
- Topic: END_user input harness.
- Replies: 1
- Views: 4189
END_user input harness.
I can't seem to find any Information about how to utilize the Input harnes that plugs into the End_User board. Do yall have a section that I've missed or something?
- Fri Jul 01, 2022 10:54 pm
- Forum: 05-06 RSX Specific
- Topic: GM 3BAR map sensor?
- Replies: 1
- Views: 2999
GM 3BAR map sensor?
Is it not possible to use a GM 3Bar map sensor? The map sensor selection only has "factory & 4Bar omnipower". If it's possible how can it be done? Can I just put the GM 3Bar scaler and offset settings and click on omnipower 4Bar? Or could I put the GM sensor setting under the factors m...
- Thu Jun 23, 2022 11:09 am
- Forum: 05-06 RSX Specific
- Topic: A3 stock map and tuned map.
- Replies: 0
- Views: 5686
A3 stock map and tuned map.
JW?
I've always used the a3 "tuned" map to start tunning from. But I was checking out the stock map and noticed it had more cam angles ? Why doesn't both the 5speed a3 maps use the same ammout of cam angles?
I've always used the a3 "tuned" map to start tunning from. But I was checking out the stock map and noticed it had more cam angles ? Why doesn't both the 5speed a3 maps use the same ammout of cam angles?
- Thu May 12, 2022 12:36 am
- Forum: 05-06 RSX Specific
- Topic: Anti lag button?
- Replies: 1
- Views: 3205
Anti lag button?
Can anti-lag be activated via a button, like my unused cruise control?
- Fri Mar 11, 2022 8:25 pm
- Forum: 05-06 RSX Specific
- Topic: lambda overlay
- Replies: 11
- Views: 16557
Re: lambda overlay
My lambda overlay cells are empty in high cam. Can I make it show data while in high cam?
- Thu Feb 10, 2022 2:58 am
- Forum: 05-06 RSX Specific
- Topic: One wire and 2 wire aftermarket temp sensors HELP...
- Replies: 1
- Views: 3458
One wire and 2 wire aftermarket temp sensors HELP...
I have my E85 plugged in my ECU "easy install", but I bought 2 temp sensors. A 1 wire and a 2 wire temp sensor, Just curious how and wich wires on the Auxiliary harnesses that came with my ktuner R1 can I run the temp wires to? I have the red black yellow white green Auxiliary ktuner harne...
- Mon Jan 17, 2022 2:24 pm
- Forum: 05-06 RSX Specific
- Topic: Fuel trims & WOT
- Replies: 4
- Views: 6340
Re: Fuel trims & WOT
I have a feeling my acuity tps is going out because my throttle has been kinda Jerky. I zero it out and it temporarily fixes it. Since it's a hall effect sensor I'm sure it goes bad with different symptoms than a brush style tps.
- Mon Jan 17, 2022 2:13 pm
- Forum: 05-06 RSX Specific
- Topic: Fuel trims & WOT
- Replies: 4
- Views: 6340
Re: Fuel trims & WOT
The stft use to go away in open loop, now it stays on correcting. The corrections only show + - 1 or 2%. It still shows roughly 13.5afr at wot, just asking. The only thing I changed Is The 20% wot and the cut off to 18%. What would cause this? My tps?
- Sun Jan 16, 2022 1:33 pm
- Forum: 05-06 RSX Specific
- Topic: Fuel trims & WOT
- Replies: 4
- Views: 6340
Fuel trims & WOT
I noticed my car still shows stft when I go In open loop after my 20% tps threshold, it never use to do this. I have a Acuity tps, I think it might be going bad. Would that cause this? The afr still shows 13.5afr it wot. The sftf just still show its trying to compensate.