Search found 122 matches
- Tue Nov 28, 2023 2:31 am
- Forum: KTuner Software
- Topic: System AFR values when in high cam
- Replies: 22
- Views: 17221
Re: System AFR values when in high cam
There is a gauge for ELD Input as well. Hello again I'd like to re-position my WBO2 input to use the gauge available in the ELD input. I can move my WBO2 signal from Ptank to ELD easily enough, what I can't find its where I disable the ELD, since I will be disconnecting the existing ELD input to do...
- Sun Nov 26, 2023 6:57 pm
- Forum: KTuner Software
- Topic: Repeated System WBO2 Failures
- Replies: 3
- Views: 1793
Re: Repeated System WBO2 Failures
OK - thank you for that info. I will look elsewhere.
Hope you had a good Thanksgiving!
Hope you had a good Thanksgiving!
- Sun Nov 26, 2023 2:18 am
- Forum: KTuner Software
- Topic: Repeated System WBO2 Failures
- Replies: 3
- Views: 1793
Repeated System WBO2 Failures
Just trying to cover all possible causes for the System WBO2 failures. '05 RSX ECU 37820-PND-A63. JDM '05 K24A3. I have installed: Bosch 15482 (actually repackaged Denso) (Sept. 2018) Denso 234-4454 (July 2021) KAX 234-9066 (Dec 2021), Denso 234-9066 (Jun 2023) Finally a Honda packaged 36531-RBB-003...
- Thu Sep 29, 2022 2:26 pm
- Forum: KTuner Software Installation
- Topic: New laptop -
- Replies: 3
- Views: 4244
Re: New laptop -
Thank you for the clarification.
- Wed Sep 28, 2022 1:00 am
- Forum: KTuner Software Installation
- Topic: New laptop -
- Replies: 3
- Views: 4244
New laptop -
When I install & run K-tuner (connected to ECU), K-Tuner will switch registration to the new laptop? Just confirming I don't need to do anything with the old laptop first... following directions (existing account) from your "Help/Account Registration" page https://i.postimg.cc/s3Nzc1jm...
- Wed Sep 21, 2022 3:36 pm
- Forum: KTuner Software
- Topic: TPS readings
- Replies: 23
- Views: 39365
Re: TPS readings
Many thanks for responding - took me awhile to find it in the general parameters - I'll make some adjustments & see how it goes.
- Wed Sep 21, 2022 12:13 am
- Forum: KTuner Software
- Topic: TPS readings
- Replies: 23
- Views: 39365
Re: TPS readings
I can make the software see 80 as 100, that's simple enough, but I prefer accurate information as relayed by the ECU. Think about the WOT settings for TPS that are set to 74%. That's because 80% as a max was clearly planned. Where do I find this? I can't find any of the WOT parameters, or find ment...
- Thu Sep 15, 2022 12:22 am
- Forum: K Swapped Vehicles
- Topic: Radiator fan wiring/ fanC
- Replies: 18
- Views: 180752
Re: Radiator fan wiring/ fanC
OK - so I get it is unused from the factory. I also read where you said it can be enabled, which I did.
You are not answering the simple question as to what the scale is in your software parameter window. Is it Celsius or Fahrenheit, or some other interpolated figure??
You are not answering the simple question as to what the scale is in your software parameter window. Is it Celsius or Fahrenheit, or some other interpolated figure??
- Wed Sep 14, 2022 1:38 am
- Forum: K Swapped Vehicles
- Topic: Radiator fan wiring/ fanC
- Replies: 18
- Views: 180752
Re: Radiator fan wiring/ fanC
You should really read the thread if you plan on replying to it. Here are two responses from this very thread. The Radiator Fan output is not used on the RSX from the factory, but can be enabled in the software on the pin labeled for the output, looking at the 05-06 side of the conversion harness. ...
- Tue Sep 13, 2022 12:11 am
- Forum: KTuner Software
- Topic: System AFR values when in high cam
- Replies: 22
- Views: 17221
Re: System AFR values when in high cam
Thank you - yes, I see it in the list. The values don't jive with the WBO2 controller, so I will have to review the table I used, it came with the controller, but something has to be wrong.