Page 2 of 4

Re: 07 accord CM5 tuning options

Posted: Sun Nov 22, 2015 12:01 pm
by KTuner
TurbogixxerTuning is one of our dealers.

Re: 07 accord CM5 tuning options

Posted: Sat Jan 16, 2016 11:14 pm
by bianyy
Can I disable Evap and EGR pins of ecu as my car dosenot have ecm controlled EVAP and EGR. The evap is a 2 way connector with no wiring to ecu,EGR is bypassed.

Re: 07 accord CM5 tuning options

Posted: Sat Jan 16, 2016 11:49 pm
by KTuner
Yes, we have disables.

Re: 07 accord CM5 tuning options

Posted: Sat Jul 14, 2018 12:57 am
by bianyy
Hi, I have 0607 end user from turbogixxer received and installed on my computer.
Before installation I need to create a basemap for K24A2, I haven't see a proper map under 0607 accord in the software. From factory 0607 RAD kcl the RPM column in all tables are designed for below 7000 RPM and cranking/idle RPM range has 5 rows and most other stock rows are seem to tuned according to low end range.

How can I rename each row in a quicker way of all tables to let them being suitable for k24a2 with a max 7500RPM and proper arranged of each row according to k24a2's hardware feature. I know that can be done one by one manually but it will take several days to do messy job.

[img]
捕获.PNG
(35.04 KiB) Not downloaded yet
[/img]

Re: 07 accord CM5 tuning options

Posted: Sat Jul 14, 2018 5:11 pm
by KTuner
You do not need this change on low cam tables, only high cam. It only needs to be done once to apply to all ignition maps and fuel maps.

Re: 07 accord CM5 tuning options

Posted: Sat Aug 25, 2018 12:52 am
by bianyy
0 cam.PNG
(29.07 KiB) Not downloaded yet
0 delta.PNG
(30.99 KiB) Not downloaded yet
0 fuel.PNG
(44.48 KiB) Not downloaded yet
HI Ktuner

I have this early stage stock K24A2 RBB engine on 07 accord and drives to work well. BTW exhaust system is still accord stock. I spent a lot time to fixed cranking fueling and low cruising area 1000-1500rpm.
1 When tuning part throttle in mid cruise range fuel number has a huge dip (some cells 30%) from 4000 to 4500 rpm with stock cam MAP from K24A2, says cam jump from 6 to 0.
What can I do next?
2 how do you recommend I adjust part throttle vtc table accordingly? I know most tuning happen on WOT but my application is focusing on cruising. At part throttle how do I know which vtc is best for each cell?
3 I noticed the number in %delta table shows how much percentage comparing stoi it has rather than how much I need to adjust, so this is a reverse setup comparing hondata's am I right? Means if it shows -10% then I need to +10% I got this conclusion from overlay lambda table and didn't see any statement in manual.?

BTW, attached file is the latest status for illustration purpose, before this modification it was all 30% on 4500rpm from 20kpa to 50 kpa and then back up a little on 5000 and then back down 5500 up again..

Re: 07 accord CM5 tuning options

Posted: Mon Aug 27, 2018 3:45 pm
by KTuner
Don't forget any CAM angle over 0 is interpolated with the next CAM map. So 0 and 10, or 0 and 15, whichever you have in the software.

Set the cam angle completely to the 0, 10, 20, etc to correct tune all of the CAM breakpoints.

It should be how far you are from your targets set in preferences.

Re: 07 accord CM5 tuning options

Posted: Wed Aug 29, 2018 1:13 am
by bianyy
KTuner wrote:Don't forget any CAM angle over 0 is interpolated with the next CAM map. So 0 and 10, or 0 and 15, whichever you have in the software.

Set the cam angle completely to the 0, 10, 20, etc to correct tune all of the CAM breakpoints.

It should be how far you are from your targets set in preferences.
Hi Ktuner

If it's interpolating algorithm, why when I lock cam to 25 during logging I can see on the screen only 20 table is highlighted and the lambada displays, nothing in 30 table is activated and not any lambada showed over there.
You can refer attached log file, I lock it to 5 degree and only 0 table is working too. Please confirm if it's only a display issue or the other issues.

Re: 07 accord CM5 tuning options

Posted: Wed Aug 29, 2018 1:38 am
by KTuner
Because it's more than 20 and not 30 or above.

Re: 07 accord CM5 tuning options

Posted: Fri Aug 31, 2018 1:55 am
by bianyy
KTuner wrote:Because it's more than 20 and not 30 or above.
From this statement I get 0 table will be used for cam 0 to 9 degree to do interpolating, am I right?
Not like my previous understood cam 25 fueling will be interploated from 20 table and 30 table?