Search found 76 matches
- Sat Jun 25, 2022 7:18 pm
- Forum: 03-06 Element Specific
- Topic: Running out of fuel?
- Replies: 13
- Views: 8623
Re: Running out of fuel?
Disregard that last post, I was wrong. Everything looks in order on my end too with the PZD tune, there are no CELs or hiccups when crossing into boost & even the cell tracing tracks accurately into the expanded table areas for boost, but the fuel values are not being used past 1000mbar. This is...
- Sat Jun 25, 2022 6:49 pm
- Forum: 03-06 Element Specific
- Topic: Running out of fuel?
- Replies: 13
- Views: 8623
Re: Running out of fuel?
Edit: This post was wrong so I removed it, thanks KTuner.
- Sat Jun 25, 2022 5:20 pm
- Forum: 03-06 Element Specific
- Topic: Running out of fuel?
- Replies: 13
- Views: 8623
Re: Running out of fuel?
This is the PZD MT with forced induction base for the Element, adjusted for larger injectors and only a couple settings changed for operability. If this doesn’t work then it means your base tune for boost does not work. The PRB base has completely different VCT tables, so I am reluctant to us it as ...
- Sat Jun 25, 2022 4:01 pm
- Forum: 03-06 Element Specific
- Topic: Running out of fuel?
- Replies: 13
- Views: 8623
Re: Running out of fuel?
Of course, isn’t that the only way to get boost support enabled?
- Sat Jun 25, 2022 9:17 am
- Forum: 03-06 Element Specific
- Topic: Running out of fuel?
- Replies: 13
- Views: 8623
Re: Running out of fuel?
Okay, so it looks like the fuel values are not changing as expected. At the start of the pull the Base Fuel Value is at 6000 & is running a little rich. https://www.dropbox.com/s/e2qle1thhbsszuv/Fuel%20Value%20Start%20of%20Pull.JPG?dl=0 Through the pull the fuel table values go from roughly 6,00...
- Fri Jun 24, 2022 5:54 pm
- Forum: 03-06 Element Specific
- Topic: Running out of fuel?
- Replies: 13
- Views: 8623
Re: Running out of fuel?
Sensor data all seems accurate, 650cc fuel injectors are new (& have been flow tested), fuel pump & filter are new (using 265lph DW pump), and I am at a loss for what else to check. General consensus from other tuners is run ridiculously oversized fuel injectors (1000cc or larger), or upgrad...
- Fri Jun 24, 2022 4:59 am
- Forum: 03-06 Element Specific
- Topic: Running out of fuel?
- Replies: 13
- Views: 8623
Running out of fuel?
I keep running out of fuel in boost and it doesnt seem to matter how much fuel I add the AFR remains the same, and this section of the fuel map goes dangerously lean. Is there something I am missing here? Off boost driving seems to be fine at all RPMs. https://www.dropbox.com/s/hrj85zct8s0l26d/STILL...
- Tue Jun 21, 2022 4:28 am
- Forum: KTuner Software
- Topic: How to clear Lambda Overlay?
- Replies: 5
- Views: 6118
How to clear Lambda Overlay?
I datalog while driving for a little bit then review the lambda overlay table, make fuel adjustments as needed, and then upload the revised tune. I have found no way to clear the datalog info (whether it was recorded or not) or reset the lambda overlay table to remove the previous values. Currently ...
- Tue Jun 14, 2022 7:05 pm
- Forum: 03-06 Element Specific
- Topic: TPS Calibration Issues (Continued)
- Replies: 12
- Views: 8384
Re: TPS Calibration Issues (Continued)
That would make sense, thanks!
- Tue Jun 14, 2022 7:03 pm
- Forum: 03-06 Element Specific
- Topic: Aftermarket Wideband in Lambda Overlay?
- Replies: 7
- Views: 5129
Re: Aftermarket Wideband in Lambda Overlay?
Okay, I think I understand now. The break point settings are blank for all of the preloaded widebands so I assumed that table was related to the serial port drop down right above it, but after adding a new wideband & entering sensor data I see the table changes as I pick different widebands. Thi...