Search found 17 matches
- Sun Jul 22, 2018 4:41 pm
- Forum: 06-09 S2000 Specific
- Topic: ECT2 and ecu connection
- Replies: 1
- Views: 7314
ECT2 and ecu connection
So which sensor exactly is ect2? Prior to my swap I had a coolant gauge and fans, im just trying to figure out what exactly is disabled. It could be my new swap harness but since its a dual ecu harness I wanted to get some info from you guys. I should of returned to factory before doing all this cau...
- Mon Aug 28, 2017 4:45 pm
- Forum: 06-09 S2000 Specific
- Topic: AFR.CMD
- Replies: 3
- Views: 8900
Re: AFR.CMD
WOT enrichment stops at atmospheric pressure so what or where is it pulling this # to target/command. Specifcally in open loop?
- Mon Aug 28, 2017 1:18 am
- Forum: 06-09 S2000 Specific
- Topic: CEL P325 ECT2 error
- Replies: 5
- Views: 9653
Re: CEL P325 ECT2 error
Thank you!
- Mon Aug 28, 2017 12:56 am
- Forum: 06-09 S2000 Specific
- Topic: AFR.CMD
- Replies: 3
- Views: 8900
AFR.CMD
can you explain this number?
I assumed commanded, but dont it has capabilities like that in boost and 0% STFTs and LTFTs.
Is this the OEM o2 "adjusted" o2?
I assumed commanded, but dont it has capabilities like that in boost and 0% STFTs and LTFTs.
Is this the OEM o2 "adjusted" o2?
- Mon Aug 21, 2017 12:28 am
- Forum: 06-09 S2000 Specific
- Topic: CEL P325 ECT2 error
- Replies: 5
- Views: 9653
Re: CEL P325 ECT2 error
My apologies its P0128 which did not come on until I had finished the repining. I couldn't chalk it up as a coincidence because when I finished it immediately started popping. Any thoughts?
- Mon Aug 21, 2017 12:24 am
- Forum: 06-09 S2000 Specific
- Topic: Flex fuel table and negative psi adjustments
- Replies: 4
- Views: 8575
- Sun Aug 20, 2017 2:22 am
- Forum: 06-09 S2000 Specific
- Topic: CEL P325 ECT2 error
- Replies: 5
- Views: 9653
CEL P325 ECT2 error
Has there been any new news on a fix for the P325 error that comes on to what i beleive is a discrepencie against the two coolant sensors showing differently during warmup. < because one is reading actual water temp and one is re routed for i cant remember which is which but its either EBC or ethano...
- Sun Aug 20, 2017 12:05 am
- Forum: 06-09 S2000 Specific
- Topic: Flex fuel table and negative psi adjustments
- Replies: 4
- Views: 8575
Re: Flex fuel table and negative psi adjustments
So on pump 91 I'm running around 15 psi with anywhere from 2%-10% ethanol at around 75ish injector duty cycle. But when I pump E85 in I need to subtract boost so my injectors don't max.
- Sat Aug 19, 2017 5:39 pm
- Forum: 06-09 S2000 Specific
- Topic: Flex fuel table and negative psi adjustments
- Replies: 4
- Views: 8575
Flex fuel table and negative psi adjustments
If I have ID1ks and actually have to reduce psi the higher the E content can I put negative (whole #'s in as "-3.1") when I save an re upload it comes back as a rounded super high number like 125.556 etc. (and looks to be a positive number) in that cell.
- Fri Jun 16, 2017 8:13 pm
- Forum: 06-09 S2000 Specific
- Topic: Ktuner PLZ help! '07 S2k ECU recovery
- Replies: 11
- Views: 19384
Re: Ktuner PLZ help! '07 S2k ECU recovery
Just out of curiosity. If it was cleared, would it had erased, flashed to 100%, finalize and then say flash fail? Cause I had tried a million different things including powering everything off. Restarting computer and just plugging the touch in, and it didnt upload or correct itself until I reinstal...