Search found 11 matches
- Thu Sep 13, 2018 6:12 pm
- Forum: 05-06 RSX Specific
- Topic: On Board Logging Parameters
- Replies: 1
- Views: 3753
On Board Logging Parameters
When setting the on board logging parameters in the "activation window" does activation occur only when all of the five parameters are met or just one (assuming my switched input is active)? Also, does the deactivation take place when all of the five parameters are met or just one? I am ac...
- Sat Apr 28, 2018 11:32 pm
- Forum: 05-06 RSX Specific
- Topic: Analog Input Display
- Replies: 3
- Views: 5744
Re: Analog Input Display
That was easy thanks. Is it possible to graph the analog inputs? I do not see them as one of the parameters that can be "added" to the graphing function.KTuner wrote:There's a table in preferences.
- Sat Apr 28, 2018 7:10 pm
- Forum: 05-06 RSX Specific
- Topic: Analog Input Display
- Replies: 3
- Views: 5744
Analog Input Display
I am using Analog Input 1 to log a external wideband. Is it possible to make the units read AFR rather than voltage so that every time I review the data I do not have to convert from voltage to AFR? I just want to confirm I am not over looking a input table to correlate voltage to AFR.
- Tue Mar 13, 2018 11:44 am
- Forum: 05-06 RSX Specific
- Topic: Anti-Theft Status
- Replies: 1
- Views: 4092
Anti-Theft Status
Is anti-theft still in beta testing? Any ETA on when it may be released in an update?
- Fri Mar 02, 2018 4:37 pm
- Forum: 05-06 RSX Specific
- Topic: Speed Input Wiring Diagram
- Replies: 11
- Views: 17545
Re: Speed Input Wiring Diagram
The wheel just needed to spin faster to register. Works perfect, thanks for the support.
- Fri Mar 02, 2018 1:30 am
- Forum: 05-06 RSX Specific
- Topic: Speed Input Wiring Diagram
- Replies: 11
- Views: 17545
Re: Speed Input Wiring Diagram
I used the RD2 cable to connect to the 4pin speed input on the ECU. 1+:Brown FRS+: GRN/BLK 1-:Green FRS-: BLU 2+: Blue RRS+: GRN/YEL 2-: Black RRS-: BLU/YEL Tested SPD1 using right front speed sensor (1+ to FRS+ and 1- to FRS-). I am receiving a VSS signal when I turn the FR wheel however no SPD1 si...
- Mon Feb 26, 2018 12:46 pm
- Forum: 05-06 RSX Specific
- Topic: Speed Input Wiring Diagram
- Replies: 11
- Views: 17545
Re: Speed Input Wiring Diagram
Simple enough. Is there a cable with pigtails that would work for making the four connections at the ECU? Perhaps the 4 pin RD2 cable work (RD2C01)?
- Sun Feb 25, 2018 4:10 am
- Forum: 05-06 RSX Specific
- Topic: Speed Input Wiring Diagram
- Replies: 11
- Views: 17545
Speed Input Wiring Diagram
Is there a wiring diagram available to wire the speed inputs to the board to enable traction control? If not Is it correct to just assume 1 front wheel gets wired to sensor 1 and 1 rear wheel to sensor 2 with can be spliced at the ABS unit?
- Tue Jun 20, 2017 8:02 pm
- Forum: 05-06 RSX Specific
- Topic: Programmable Outputs (Water/Methanol Wiring)
- Replies: 3
- Views: 6316
Re: Programmable Outputs (Water/Methanol Wiring)
As we have previously discussed I have set up a input (switch) to activate my water/methanol system. http://i.imgur.com/swbD4Uw.jpg I am looking to purchase a fail safe (Safe Injection) unit for my system. In the event of no flow it triggers a 12V signal. E16 with 12V applied the ground = off. If 12...
- Tue Apr 11, 2017 12:34 pm
- Forum: 05-06 RSX Specific
- Topic: Programmable Outputs (Water/Methanol Wiring)
- Replies: 3
- Views: 6316
Programmable Outputs (Water/Methanol Wiring)
I am looking to run a water/methanol setup and wish to run the activation through Ktuner like many have done with Kpro using the E21 input and E22 output (Nitrous tab). I can not find a schematic on what wires are used for the 6 programmable inputs/outputs that are available. Any input would be grea...